Jan 13, 2011. Messages. 2,562. Mar 14, 2014. #5. The multi-cut files are nice, like Pegs said. Really though, a sharp smooth single cut will still beat using a dull bastard cut file. So just start dusting those files off and see what works for you. The advantages of moving past the files to stones ARE very much worthwhile in my opinion.

Read On

Tools needed to sharpen an axe are a file, a honing stone, and a strop. A flat, mill bastard file should be used if your axe is extremely dull. After using the file (if needed) finish with a flat or puck style medium and then fine hone. When sharpening your axe be mindful of the bevel or angle at the bit end. can you sharpen an AXE with a knife ...

Read On

Secure the Axe for Sharpening. If you have a bench vise that allows access to the axe on both sides, this is the most secure way to hold an axe for sharpening. If not, improvise a vise with available materials. Two bricks on either side of the axe head, each held down by a carpenter's clamp, is one way to hold an axe upright.

Read On

Axe sharpening with a grinder creates a rougher finish, but it should be free of nicks and dents. When finished, use a bit of oil or wax to protect the axe head. How to Sharpen an Axe with a Sharpening Stone Adobe. The most old-school of axe grinding methods is …

Read On

Use a belt sander for the initial burring then switch to a mill file or stone to finely hone the edge. ... How to sharpen an axe without tools. ... There is nothing better than a good old mill or bastard file to get a razor sharp edge to your axe. There are many other options for sharpening an axe such as grinders, belt sanders, whetstones ...

Read On

toxonixs post about building a wet grinder got me thinking about the old pedal powered grinding stones. A friend of mine has one in his living room as decoration. It has a cast Iron seat on it, kind of like an old tractor seat, then pedals to turn the wheel. The wheel itself is approximately 30 i...

Read On

I remain convinced that the best way to sharpen an axe is the old-fashioned way – by hand, using simple tools such as a file and sharpening stone. There is little risk of damaging your axe like you might with a power tool, and it doesn't take much longer, either – if the axe is even somewhat decently maintained, re-sharpening it shouldn ...

Read On

Step one : Use a marker on the edge, try a pass with the medium rods in the 20 degrees sharpmaker settings, if this hits the edge continue until sharp then repeat with the fine rods. If it doesn't hit the edge go to step two. Step two : Take a mill bastard file and grind the edge down a little. Go back to step one.

Read On

Match the wheel to the metal being sharpened - it is the right tool for the job rule that always applies. For old tools, you may want to go with a 60 grit aluminum oxide wheel and medium hardness. Put the tools in your oven - not …

Read On

Tools needed to sharpen an axe are a file, a honing stone, and a strop. A flat, mill bastard file should be used if your axe is extremely dull. After using the file (if needed) finish with a flat or puck style medium and then fine hone. When sharpening …

Read On

Axe. The Axe was a tool used for hunting, cutting, planting, and protection purposes. It was used for cutting plants, trees, and branches. Axe was a tool used for hunting purposes as well due to its sharpness and strength, and easier use it …

Read On

I use a file first on an old axe I'm re-hafting to get the profile. Then I like to sit out in the yard in a lawn chair with a bowl of water where I soak the puck. I also have an old toothbrush to clean the puck every once in a while I'm sharpening. I hardly ever sharpen an axe on a camping trip. I just do it at my house on a nice day or evening.

Read On

Repeat this action with sandpaper that has a finer grit. Last, apply metal polish onto the axe using an old rag. Clamp Your Axe Horizontally in a Vise. You should tilt your axe at a twenty or 30-degree angle — this is the angle of the bevel. Use a Bastard File. The best option for most axes is a bastard mill file of 25-30cm.

Read On

That's caused by a bad file, a dirty file, or both. Easily cleaned up by using a diamond stone, but it takes more time the deeper the scoring. I used an old, abused file. Time to make some strikers. Once the edge and angle is established, finish the work with a DMT Duo-Fold. There are four grits commonly used, as seen in the picture.

Read On

A Grinding Wheel, a Mill File and a Sharpening Stone You can sharpen most garden tools with a simple 10-in. mill bastard file (Photo 5). A synthetic …

Read On

The Sharpening Stroke. Place the tip of the file on the left side of the tool head. Try to match the angle of the file with the bevel on the blade, usually around 30 degrees. Push the file forward and to the right, so that you end up on the …

Read On

To sharpen an axe, start by rubbing the edge of the axe with honing oil or sewing machine oil. Next, rub the tip of a coarse whetstone along the edge in a circular motion. Make sure to sharpen both sides …

Read On

Grip the axe with a vice firmly: A vice would be very important tool to avoid the movement of the axe when sharpening. The major problem people have while filing an edge is axe movement which causes slipping. So, it would be a great technique to clamp the axe with a file in order to avoid slipping. Choose a 10-12-inch mill file:

Read On

The Best Way to Sharpen an Axe – Tools You Need. 12″ Medium-Grade Mill File – I use a Nicolson file, they are made in America and they are readily available at home depot and your local hardware stores. They cost …

Read On